View EMC1402-2-ACZL-TR_944499.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

EMC1402 1C Temperature Sensor with Beta Compensation
PRODUCT FEATURES
GENERAL DESCRIPTION The EMC1402 is a high accuracy, low cost, System Management Bus (SMBus) temperature sensor. Advanced features such as Resistance Error Correction (REC), Beta Compensation (to support 90nm and 65nm CPU diodes) and automatic diode type detection combine to provide a robust solution for complex environmental monitoring applications. Each device provides 1 accuracy for external diode temperatures and 2C accuracy for the internal diode temperature. The EMC1402 monitors two temperature channels (one external and one internal). Resistance Error Correction automatically eliminates the temperature error caused by series resistance allowing greater flexibility in routing thermal diodes. Beta Compensation eliminates temperature errors caused by low, variable beta transistors common in today's fine geometry processors. The automatic beta detection feature monitors the external diode/transistor and determines the optimum sensor settings for accurate temperature measurements regardless of processor technology. This frees the user from providing unique sensor configurations for each temperature monitoring application. These advanced features plus 1C measurement accuracy provide a low-cost, highly flexible and accurate solution for critical temperature monitoring applications. APPLICATIONS Notebook Computers Desktop Computers Industrial Embedded applications
Datasheet
FEATURES Support for 90nm and 65nm CPU diodes Pin compatible with ADM1032, MAX6649, and LM99 Automatically determines external diode type and optimal settings Resistance Error Correction External Temperature Monitors
-- 1C Accuracy (60C < TDIODE < 100C) -- 0.125C Resolution
Internal Temperature Monitor
-- 2C accuracy
3.3V Supply Voltage Programmable temperature limits for ALERT and THERM Small 8-pin MSOP Lead-free RoHS Compliant Package EMC1402 PIN DESCRIPTION
VDD DP DN THERM
1 2 3 4
8 7 6 5
SMCLK SMDATA ALERT GND
SMSC EMC1402
DATASHEET
Revision 1.16 (03-15-07)
1C Temperature Sensor with Beta Compensation Datasheet
ORDER NUMBERS: EMC1402-1-ACZL-TR FOR 8 PIN, MSOP LEAD-FREE ROHS COMPLIANT PACKAGE EMC1402-2-ACZL-TR FOR 8 PIN, MSOP LEAD-FREE ROHS COMPLIANT PACKAGE
Note: See Table 1.1, "Part Selection" for SMBus addressing options.
80 ARKAY DRIVE, HAUPPAUGE, NY 11788 (631) 435-6000, FAX (631) 273-3123 Copyright (c) 2007 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information sufficient for construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no responsibility is assumed for inaccuracies. SMSC reserves the right to make changes to specifications and product descriptions at any time without notice. Contact your local SMSC sales office to obtain the latest specifications before placing your product order. The provision of this information does not convey to the purchaser of the described semiconductor devices any licenses under any patent rights or other intellectual property rights of SMSC or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may contain design defects or errors known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly sheets are available upon request. SMSC products are not designed, intended, authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property damage. Any and all such uses without prior written approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of this document or other SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC's website at http://www.smsc.com. SMSC is a registered trademark of Standard Microsystems Corporation ("SMSC"). Product names and company names are the trademarks of their respective holders. SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT; TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS HELD TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Revision 1.16 (03-15-07)
2
SMSC EMC1402
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
SMSC EMC1402
3
Revision 1.16 (03-15-07)
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
Table of Contents
Chapter 1 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.1 Part Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Chapter 2 Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Chapter 3 Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.1 3.2 3.3 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 SMBus Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Chapter 4 System Management Bus Interface Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 System Management Bus Interface Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Write Byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Read Byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Send Byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Receive Byte. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Alert Response Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SMBus Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SMBus Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 13 14 14 14 14 15 15
Chapter 5 Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.1 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1.1 Conversion Rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1.2 Dynamic Averaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . THERM Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ALERT Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.3.1 ALERT Pin Interrupt Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.3.2 ALERT Pin Comparator Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Beta Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Resistance Error Correction (REC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Programmable External Diode Ideality Factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diode Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Consecutive Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Digital Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Temperature Monitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Temperature Measurement Results and Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . External Diode Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 17 17 17 18 18 18 18 18 19 19 19 19 21 21 22
5.2 5.3
5.4 5.5 5.6 5.7 5.8 5.9 5.10 5.11 5.12
Chapter 6 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 6.10 6.11 6.12 Data Read Interlock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Temperature Data Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Conversion Rate Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Limit Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Scratchpad Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . One Shot Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Therm Limit Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Channel Mask Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Consecutive ALERT Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Beta Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
26 26 26 27 28 29 30 30 30 31 31 33
Revision 1.16 (03-15-07)
SMSC EMC1402
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
6.13 6.14 6.15 6.16 6.17
External Diode Ideality Factor Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Filter Control Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SMSC ID Register (FEh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Revision Register (FFh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
34 35 35 35 36
Chapter 7 Package Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
SMSC EMC1402
5
Revision 1.16 (03-15-07)
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
List of Figures
Figure 4.1 Figure 5.1 Figure 5.2 Figure 5.3 Figure 5.4 Figure 5.5 Figure 7.1 SMBus Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Diagram for EMC1402 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Temperature Filter Step Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Temperature Filter Impulse Response. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Block Diagram of Temperature Monitoring Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diode Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 PIN MSOP / TSSOP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 16 20 20 21 23 37
Revision 1.16 (03-15-07)
6
SMSC EMC1402
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
List of Tables
Table 1.1 Part Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Table 2.1 EMC1402 Preliminary Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Table 3.1 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Table 3.2 Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Table 3.3 SMBus Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Table 4.1 Protocol Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Table 4.2 Write Byte Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Table 4.3 Read Byte Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Table 4.4 Send Byte Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Table 4.5 Receive Byte Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Table 4.6 Alert Response Address Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Table 5.1 Supply Current vs. Conversion Rate for EMC1402 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Table 5.2 EMC1402 Temperature Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Table 6.1 Register Set in Hexadecimal Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Table 6.2 Temperature Data Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Table 6.3 Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Table 6.4 Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Table 6.5 Conversion Rate Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Table 6.6 Conversion Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Table 6.7 Temperature Limit Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Table 6.8 Scratchpad Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Table 6.9 One Shot Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Table 6.10 Therm Limit Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Table 6.11 Channel Mask Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Table 6.12 Consecutive ALERT Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Table 6.13 Consecutive Alert / THERM Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Table 6.14 Beta Configuration Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Table 6.15 CPU Beta Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Table 6.16 Ideality Configuration Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Table 6.17 Ideality Factor Look-Up Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Table 6.18 Filter Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Table 6.19 Filter Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Table 6.20 Product ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Table 6.21 Manufacturer ID Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Table 6.22 Revision Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
SMSC EMC1402
7
Revision 1.16 (03-15-07)
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
Chapter 1 Block Diagram
VDD EMC1402
Conversion Rate Register Low Limit Registers Switching Current Limit Comparator High Limit Registers SMBus Interface THERM Limit Register THERM Hysteresis Register Internal Temp Diode Configuration Register Status Registers Interupt Masking SMCLK SMDATA ALERT THERM GND
Digital Mux
Analog Mux DP1
ADC
External Temperature Register(s)
DN1
Internal Temperature Register
1.1
Part Selection
The EMC1402 device configuration is highlighted below.
Table 1.1 Part Selection
FUNCTIONALITY DIODE 2 DEFAULT CONFIGURATION N/A
PART NUMBER EMC1402 - 1 EMC1402 - 2
SMBUS ADDRESS 100_1100b 100_1101b
EXTERNAL DIODES 1
DIODE 1 DEFAULT CONFIGURATION Detect Diode w/ REC enabled
Digital Mux
OTHER Software programmable and maskable High Limits Software programmable THERM Limits
PRODUCT ID 20h
Revision 1.16 (03-15-07)
8
SMSC EMC1402
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
Chapter 2 Pin Description
Table 2.1 EMC1402 Preliminary Pin Description PIN NUMBER 1 2 3 4 5 6 7 8 VDD DP DN THERM GND ALERT SMDATA SMCLK NAME FUNCTION Power supply External diode positive (anode) connection External diode negative (cathode) connection Active low Critical THERM output signal - requires pull-up resistor Ground Active low digital ALERT output signal - requires pull-up resistor, SMBus Data input/output SMBus Clock input Power AIO AIO OD Power OD DIOD DI TYPE
The pin types are described below: Power - these pins are used to supply either VDD or GND to the device. AIO - Analog Input / Output. DI - Digital Input. OD - Open Drain Digital Output. DIOD - Digital Input / Open Drain Output.
SMSC EMC1402
9
Revision 1.16 (03-15-07)
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
Chapter 3 Electrical Specifications
3.1 Absolute Maximum Ratings
Table 3.1 Absolute Maximum Ratings DESCRIPTION Supply Voltage (VDD) Voltage on SMDATA and SMCLK pins Voltage on any other pin to Ground Operating Temperature Range Storage Temperature Range Lead Temperature Range Package Thermal Characteristics for MSOP-8 Thermal Resistance (j-a) ESD Rating, All pins HBM 140.8 2000 C/W V RATING -0.3 to 5.0 -0.3 to 5.5 -0.3 to VDD +0.3 -40 to +125 -55 to +150 Refer to JEDEC Spec. J-STD020 UNIT V V V C C
Note: Stresses at or above those listed could cause permanent damage to the device. This is a stress rating only and functional operation of the device at any other condition above those indicated in the operation sections of this specification is not implied. When powering this device from laboratory or system power supplies, it is important that the Absolute Maximum Ratings not be exceeded or device failure can result. Some power supplies exhibit voltage spikes on their outputs when the AC power is switched on or off. In addition, voltage transients on the AC power line may appear on the DC output. If this possibility exists, it is suggested that a clamp circuit be used.
3.2
Electrical Specifications
Table 3.2 Electrical Specifications VDD = 3.0V to 3.6V, TA = -40C to 125C, all typical values at TA = 27C unless otherwise noted.
CHARACTERISTIC
SYMBOL
MIN
TYP
MAX
UNITS
CONDITIONS
DC Power Supply Voltage Supply Current VDD IDD 3.0 3.3 150 750 3.6 220 V uA uA 1 conversion / sec, dynamic averaging disabled > 16 conversions / sec, dynamic averaging enabled
Revision 1.16 (03-15-07)
10
SMSC EMC1402
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
Table 3.2 Electrical Specifications (continued) VDD = 3.0V to 3.6V, TA = -40C to 125C, all typical values at TA = 27C unless otherwise noted. CHARACTERISTIC SYMBOL MIN TYP MAX UNITS CONDITIONS
Internal Temperature Monitor Temperature Accuracy 0.25 1 2 Temperature Resolution 0.125 C C C 0C < TA < 85C
External Temperature Monitor Temperature Accuracy 0.25 0.5 Temperature Resolution Conversion Time all Channels Capacitive Filter tCONV CFILTER 0.125 190 2.2 2.5 1 2 C C C ms nF EMC1402, default settings Connected across external diode +20C < TDIODE < +100C 0C < TA < 85C -40C < TDIODE < 127C
ALERT and THERM pins Output Low Voltage VOL 0.4 V ISINK = 8mA
SMSC EMC1402
11
Revision 1.16 (03-15-07)
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
3.3
SMBus Electrical Characteristics
Table 3.3 SMBus Electrical Specifications VDD = 3.0V to 3.6V, TA = -40C to 125C, all typical values are at TA = 27C unless otherwise noted.
CHARACTERISTIC
SYMBOL
MIN
TYP
MAX
UNITS
CONDITIONS
SMBus Interface Input High Voltage Input Low Voltage Input High/Low Current Input High/ Low Current Hysteresis Input Capacitance Output Low Sink Current CIN IOL 8.2 420 5 15 SMBus Timing Clock Frequency Spike Suppression Bus free time Start to Stop Hold Time: Start Setup Time: Start Setup Time: Stop Data Hold Time Data Setup Time Clock Low Period Clock High Period Clock/Data Fall time Clock/Data Rise time Capacitive Load fSMB tSP tBUF tHD:STA tSU:STA tSU:STP tHD:DAT tSU:DAT tLOW tHIGH tFALL tRISE CLOAD 1.3 0.6 0.6 0.6 0.3 100 1.3 0.6 300 300 400 10 400 50 kHz ns us us us us us ns us us ns ns pF Min = 20+0.1CLOAD ns Min = 20+0.1CLOAD ns per bus line VIH VIL IIH / IIL 2.0 -0.3 -1 VDD 0.8 1 TBD V V uA uA mV pF mA SMDATA = 0.4V 5V Tolerant 5V Tolerant TA = 27C, SMDATA / SMCLK = 0V to VDD SMDATA / SMCLK = 0V to 5.5V
Revision 1.16 (03-15-07)
12
SMSC EMC1402
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
Chapter 4 System Management Bus Interface Protocol
4.1 System Management Bus Interface Protocol
TheEMC1402 communicates with a host controller, such as an SMSC SIO, through the SMBus. The SMBus is a two-wire serial communication protocol between a computer host and its peripheral devices. A detailed timing diagram is shown in Figure 4.1.
.
TLOW
THIGH
THD:STA TSU:STO
SMCLK
THD:STA
TRISE
TFALL
THD:DAT
TSU:DAT
TSU:STA
SMDTA
TBUF
P
S
S - Start Condition
S
P - Stop Condition
P
Figure 4.1 SMBus Timing Diagram The EMC1402 is SMBus 2.0 compatible and support Send Byte, Read Byte, Write Byte, Receive Byte, and the Alert Response Address as valid protocols as shown below. All of the below protocols use the convention in Table 4.1.
Table 4.1 Protocol Format DATA SENT TO DEVICE # of bits sent DATA SENT TO THE HOST # of bits sent
Attempting to communicate with the EMC1402 SMBus interface with an invalid slave address or invalid protocol will result in no response from the device and will not affect its register contents. Stretching of the SMCLK signal is supported, provided other devices on the SMBus control the timing.
4.2
Write Byte
The Write Byte is used to write one byte of data to the registers as shown below Table 4.2:
Table 4.2 Write Byte Protocol SLAVE ADDRESS 7 REGISTER ADDRESS 8 REGISTER DATA 8
START 1
WR 1
ACK 1
ACK 1
ACK 1
STOP 1
SMSC EMC1402
13
Revision 1.16 (03-15-07)
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
4.3
Read Byte
The Read Byte protocol is used to read one byte of data from the registers as shown in Table 4.3.
Table 4.3 Read Byte Protocol
START SLAVE ADDRESS WR ACK REGISTER ADDRESS ACK START SLAVE ADDRESS RD ACK REGISTER DATA NACK STOP
1
7
1
1
8
1
1
7
1
1
8
1
1
4.4
Send Byte
The Send Byte protocol is used to set the internal address register pointer to the correct address location. No data is transferred during the Send Byte protocol as shown in Table 4.4.
Table 4.4 Send Byte Protocol SLAVE ADDRESS 7 REGISTER ADDRESS 8
START 1
WR 1
ACK 1
ACK 1
STOP 1
4.5
Receive Byte
The Receive Byte protocol is used to read data from a register when the internal register address pointer is known to be at the right location (e.g. set via Send Byte). This is used for consecutive reads of the same register as shown in Table 4.5.
Table 4.5 Receive Byte Protocol SLAVE ADDRESS 7
START 1
RD 1
ACK 1
REGISTER DATA 8
NACK 1
STOP 1
4.6
Alert Response Address
The ALERT output can be used as a processor interrupt or as an SMBus Alert. When it detects that the ALERT pin is asserted, the host will send the Alert Response Address (ARA) to the general address of 000_1100b. All devices with active interrupts will respond with their client address as shown in Table 4.6.
Table 4.6 Alert Response Address Protocol ALERT RESPONSE ADDRESS 7
START 1
RD 1
ACK 1
DEVICE ADDRESS 8
NACK 1
STOP 1
Revision 1.16 (03-15-07)
14
SMSC EMC1402
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
The EMC1402 will respond to the ARA in the following way: 1. Send Slave Address and verify that full slave address was sent (i.e. the SMBus communication from the device was not prematurely stopped due to a bus contention event). 2. Set the MASK bit to clear the ALERT pin. APPLICATION NOTE: The ARA does not clear the Status Register and if the MASK bit is cleared prior to the Status Register being cleared, the ALERT pin will be reasserted.
4.7
SMBus Address
The EMC1402-2 responds to hard-wired SMBus slave address as shown in Table 1.1. Note: Other addresses are available. Contact SMSC for more information.
4.8
SMBus Timeout
The EMC1402 supports SMBus Timeout. If the clock line is held low for longer than 30ms, the device will reset its SMBus protocol. This function can be disabled by clearing the TIMEOUT bit in the Consecutive Alert Register (see Section 6.11).
SMSC EMC1402
15
Revision 1.16 (03-15-07)
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
Chapter 5 Product Description
The EMC1402 is an SMBus temperature sensor. The EMC1402 monitors one internal diode and one externally connected temperature diode. Thermal management is performed in cooperation with a host device. This consists of the host reading the temperature data of both the external and internal temperature diodes of the EMC1402 and using that data to control the speed of one or more fans. The EMC1402 has two levels of monitoring. The first provides a maskable ALERT signal to the host when the measured temperatures exceeds user programmable limits. This allows the EMC1402 to be used as an independent thermal watchdog to warn the host of temperature hot spots without direct control by the host. The second level of monitoring provides a non maskable interrupt on the THERM pin if the measured temperatures meet or exceed a second programmable limit. Since the EMC1402 automatically corrects for temperature errors due to series resistance in temperature diode lines, there is greater flexibility in where external diodes are positioned and better measurement accuracy than previously available with non-resistance error correcting devices. The automatic beta detection feature means that there is no need to program the device according to which type of diode is present. Therefore, the EMC1402 can power up ready to operate for any system configuration. Figure 5.1 shows a system level block diagram of the EMC1402.
CPU
EMC1402
DP1 DN1 Internal Diode
Host SMCLK SMDATA ALERT THERM SMBus Interface
Thermal diode
Power Control
Figure 5.1 System Diagram for EMC1402
5.1
Modes of Operation
The EMC1402 has two modes of operation. Active (Run) - In this mode of operation, the ADC is converting on all temperature channels at the programmed conversion rate. The temperature data is updated at the end of every conversion and the limits are checked. In Active mode, writing to the one-shot register will do nothing. Standby (Stop) - In this mode of operation, the majority of circuitry is powered down to reduce supply current. The temperature data is not updated and the limits are not checked. In this mode of operation, the SMBus is fully active and the part will return requested data. Writing to the oneshot register will enable the device to update all temperature channels. Once all the channels are updated, the device will return to the Standby mode.
Revision 1.16 (03-15-07)
16
SMSC EMC1402
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
5.1.1
Conversion Rates
The EMC1402 may be configured for different conversion rates based on the system requirements. The conversion rate is configured as described in Section 6.5. The default conversion rate is 4 conversions per second. Other available conversion rates are shown in Table 6.6.
5.1.2
Dynamic Averaging
Dynamic averaging causes the EMC1402 to measure the external diode channels for an extended time based on the selected conversion rate. This functionality can be disabled for increased power savings at the lower conversion rates (see Section 6.4). When dynamic averaging is enabled, the device will automatically adjust the sampling and measurement time for the external diode channels. This allows the device to average 2x or 16x longer than the normal 11 bit operation (nominally 21ms per channel) while still maintaining the selected conversion rate. The benefits of dynamic averaging are improved noise rejection due to the longer integration time as well as less random variation of the temperature measurement. When enabled, the dynamic averaging applies when a one-shot command is issued. The device will perform the desired averaging during the one-shot operation according to the selected conversion rate. When enabled, the dynamic averaging will affect the average supply current based on the chosen conversion rate as shown in Table 5.1 for the EMC1402.
Table 5.1 Supply Current vs. Conversion Rate for EMC1402 AVERAGING FACTOR (BASED ON 11-BIT OPERATION) ENABLED (DEFAULT) 16x 16x 16x 16x 16x 16x 8x 4x 2x 1x 0.5x
AVERAGE SUPPLY CURRENT ENABLED (DEFAULT) 120uA 135uA 165uA 230uA 365uA 625uA 660uA 725uA 730uA 745uA 775uA
CONVERSION RATE 1 / 16 sec 1 / 8 sec 1 / 4 sec 1 / 2 sec 1 / sec 2 / sec 4 / sec (default) 8 / sec 16 / sec 32 / sec 64 / sec
DISABLED 100uA 105uA 110uA 115uA 130uA 165uA 225uA 350uA 485uA 745uA 775uA
DISABLED 1x 1x 1x 1x 1x 1x 1x 1x 1x 1x 0.5x
5.2
THERM Output
The THERM output is asserted independently of the ALERT output and cannot be masked. Whenever any of the measured temperatures exceed the user programmed THERM Limit values for the programmed number of consecutive measurements, the THERM output is asserted. Once it has been asserted, it will remain asserted until all measured temperatures drop below the THERM Limit minus the THERM Hysteresis (also programmable).
SMSC EMC1402
17
Revision 1.16 (03-15-07)
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
When the THERM pin is asserted, the Therm status bits will likewise be set. Reading these bits will not clear them until the THERM pin is deasserted. Once the THERM pin is deasserted, the THERM status bits will be automatically cleared.
5.3
ALERT Output
The ALERT pin is an open drain output and requires a pull-up resistor to VDD and has two modes of operation: interrupt mode and comparator Mode. The mode of the ALERT output is selected via the ALERT / COMP bit in the Configuration Register (see Section 6.4).
5.3.1
ALERT Pin Interrupt Mode
When configured to operate in interrupt mode, the ALERT pin asserts low when an out of limit measurement (> high limit or < low limit) is detected on any diode or when a diode fault is detected. The ALERT pin will remain asserted as long as an out-of-limit condition remains. Once the out-of-limit condition has been removed, the ALERT pin will remain asserted until the appropriate status bits are cleared. The ALERT pin can be masked by setting the MASK bit. Once the ALERT pin has been masked, it will be de-asserted and remain de-asserted until the MASK bit is cleared by the user. Any interrupt conditions that occur while the ALERT pin is masked will update the Status Register normally. The ALERT pin is used as an interrupt signal or as an Smbus Alert signal that allows an SMBus slave to communicate an error condition to the master. One or more ALERT outputs can be hard-wired together.
5.3.2
ALERT Pin Comparator Mode
When the ALERT pin is configured to operate in comparator mode it will be asserted if if any of the measured temperatures exceeds the respective high limit. The ALERT pin will remain asserted until all temperatures drop below the corresponding high limit minus the THERM Hysteresis value. When the ALERT pin is asserted in comparator mode, the corresponding high limit status bits will be set. Reading these bits will not clear them until the ALERT pin is deasserted. Once the ALERT pin is deasserted, the status bits will be automatically cleared. The MASK bit will not block the ALERT pin in this mode, however the individual channel masks (see Section 6.10) will prevent the respective channel from asserting the ALERT pin.
5.4
Beta Compensation
The EMC1402 is configured to monitor the temperature of basic diodes (e.g. 2N3904), or CPU thermal diodes. It automatically detects the type of external diode (CPU diode or diode connected transistor) and determines the optimal setting to reduce temperature errors introduced by beta variation. For discrete transistors configured with the collector and base shorted together, the beta is generally sufficiently high such that the percent change in beta variation is very small. For example, a 10% variation in beta for two forced emitter currents with a transistor whose ideal beta is 50 would contribute approximately 0.25C error at 100C. However for substrate transistors where the base-emitter junction is used for temperature measurement and the collector is tied to the substrate, the proportional beta variation will cause large error. For example, a 10% variation in beta for two forced emitter currents with a transistor whose ideal beta is 0.5 would contribute approximately 8.25C error at 100C.
5.5
Resistance Error Correction (REC)
Parasitic resistance in series with the external diodes will limit the accuracy obtainable from temperature measurement devices. The voltage developed across this resistance by the switching diode currents cause the temperature measurement to read higher than the true temperature.
Revision 1.16 (03-15-07)
18
SMSC EMC1402
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
Contributors to series resistance are PCB trace resistance, on die (i.e. on the processor) metal resistance, bulk resistance in the base and emitter of the temperature transistor. Typically, the error caused by series resistance is +0.7C per ohm. The EMC1402 automatically corrects up to 100 ohms of series resistance.
5.6
Programmable External Diode Ideality Factor
The EMC1402 is designed for external diodes with an ideality factor of 1.008. Not all external diodes, processor or discrete, will have this exact value. This variation of the ideality factor introduces error in the temperature measurement which must be corrected for. This correction is typically done using programmable offset registers. Since an ideality factor mismatch introduces an error that is a function of temperature, this correction is only accurate within a small range of temperatures. To provide maximum flexibility to the user, the EMC1402 provides a 6-bit register for each external diode where the ideality factor of the diode used is programmed to eliminate errors across all temperatures.
APPLICATION NOTE: When monitoring a substrate transistor or CPU diode and beta compensation is enabled, the Ideality Factor should not be adjusted. Beta Compensation automatically corrects for most ideality errors.
5.7
Diode Faults
The EMC1402 detects an open on the DP and DN pins, and a short across the DP and DN pins. For each temperature measurement made, the device checks for a diode fault on the external diode channel(s). When a diode fault is detected, the ALERT pin asserts (unless masked, see Section 5.8) and the temperature data reads 00h in the MSB and LSB registers (note: the low limit will not be checked). A diode fault is defined as one of the following: an open between DP and DN, a short from Vdd to DP, or a short from Vdd to DN. If a short occurs across DP and DN or a short occurs from DP to GND, the low limit status bit is set and the ALERT pin asserts (unless masked). This condition is indistinguishable from a temperature measurement of 0.000degC (-64C in extended range) resulting in temperature data of 00h in the MSB and LSB registers. If a short from DN to GND occurs (with a diode connected), temperature measurements will continue as normal with no alerts.
5.8
Consecutive Alerts
The EMC1402 contains multiple consecutive alert counters. One set of counters applies to the ALERT pin and the second set of counters applies to the THERM pin. Each temperature measurement channel has a separate consecutive alert counter for each of the ALERT and THERM pins. All counters are user programmable and determine the number of consecutive measurements that a temperature channel(s) must be out-of-limit or reporting a diode fault before the corresponding pin is asserted. See Section 6.11 for more details on the consecutive alert function.
5.9
Digital Filter
To reduce the effect of noise and temperature spikes on the reported temperature, the External Diode channel uses a programmable digital filter. This filter can be configured as Level 1, Level 2, or Disabled. The typical filter performance is shown in Figure 5.2 and Figure 5.3.
SMSC EMC1402
19
Revision 1.16 (03-15-07)
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
Filter Step Response
90 Temperature (C) 80 70 60 50 40 30 20 10 0 0 2 4 6 Samples 8 10 12 14
Disabled Level1 Level2
Figure 5.2 Temperature Filter Step Response
Filter Impulse Response
90 80 Temperature (C) 70 60 50 40 30 20 10 0 0 2 4 6 8 10 12 14 Samples
Figure 5.3 Temperature Filter Impulse Response
Disabled
Level1 Level2
Revision 1.16 (03-15-07)
20
SMSC EMC1402
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
5.10
Temperature Monitors
In general, thermal diode temperature measurements are based on the change in forward bias voltage of a diode when operated at two different currents. This VBE is proportional to absolute temperature as shown in the following equation:
where:
V BE =
kT
q
I ln HIGH I LOW

k = Boltzmann's constant T = absolute temperature in Kelvin q = electron charge [1]
= diode ideality factor
Figure 5.4 shows a block diagram of the temperature measurement circuit. The negative terminal for the remote temperature diode, DN, is internally biased with a forward diode voltage referenced to ground.
ILOW
IHIGH
Substrate PNP
DP Resistance Error Correction DN AntiAliasing Filter ADC
Figure 5.4 Block Diagram of Temperature Monitoring Circuit
5.11
Temperature Measurement Results and Data
The temperature measurement results are stored in the internal and external temperature registers. These are then compared with the values stored in the high and low limit registers. Both external and internal temperature measurements are stored in 11-bit format with the eight (8) most significant bits stored in a high byte register and the three (3) least significant bits stored in the three (3) MSB positions of the low byte register. All other bits of the low byte register are set to zero. The EMC1402 has two selectable temperature ranges. The default range is from 0C to +127C and the temperature is represented as binary number able to report a temperature from 0C to +127.875C in 0.125C steps. The extended range is an extended temperature range from -64C to +191C. The data format is a binary number offset by 64C. The extended range is used to measure temperature diodes with a large known offset (such as AMD processor diodes) where the diode temperature plus the offset would be equivalent to a temperature higher than +127C.
SMSC EMC1402
21
Revision 1.16 (03-15-07)
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
Table 5.2 shows the default and extended range formats.
Table 5.2 EMC1402 Temperature Data Format EXTENDED RANGE RANGE -64C TO 191C 000 0000 0000 000 0000 0000 Note 5.2 001 1111 1111 010 0000 0000 010 0000 0001 010 0000 1000 100 0000 0000 100 0000 1000 101 1111 1000 101 1111 1111 110 0000 0000 111 1111 0000 111 1111 1000 111 1111 1111 Note 5.4
TEMPERATURE (C) Diode Fault -64 -1 0 0.125 1 64 65 127 127.875 128 190 191 >= 191.875
DEFAULT RANGE 0C TO 127C 000 0000 0000 000 0000 0000 000 0000 0000 000 0000 0000 Note 5.1 000 0000 0001 000 0000 1000 010 0000 0000 010 0000 1000 011 1111 1000 011 1111 1111 011 1111 1111 Note 5.3 011 1111 1111 011 1111 1111 011 1111 1111
Note 5.1 Note 5.2 Note 5.3 Note 5.4
In default mode, all temperatures < 0C will be reported as 0C. In the extended range, all temperatures < -64C will be reported as -64C. For the default range, all temperatures > +127.875C will be reported as +127.875C. For the extended range, all temperatures > +191.875C will be reported as +191.875C.
5.12
External Diode Connections
The EMC1402 can be configured to measure a CPU substrate transistor, a discrete 2N3904 thermal diode, or an AMD processor diode. The diode can be connected in a variety of ways as indicated in Figure 5.5.
Revision 1.16 (03-15-07)
22
SMSC EMC1402
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
to DP to DN
to DP
to DP
to DN Local Ground Typical remote substrate transistor i.e. CPU substrate PNP Typical remote discrete PNP transistor i.e. 2N3906
Figure 5.5 Diode Configurations
to DN
Typical remote discrete NPN transistor i.e. 2N3904
SMSC EMC1402
23
Revision 1.16 (03-15-07)
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
Chapter 6 Register Description
The registers shown in Table 6.1 are accessible through the SMBus. An entry of `-' indicates that the bit is not used and will always read `0'.
Table 6.1 Register Set in Hexadecimal Order REGISTER ADDRESS 00h 01h 02h DEFAULT VALUE 00h Page 26 R R-C External Diode Data High Byte Status Stores the integer data for the External Diode Stores status bits for the Internal Diode and External Diodes Controls the general operation of the device (mirrored at address 09h) Controls the conversion rate for updating temperature data (mirrored at address 0Ah) Stores the 8-bit high limit for the Internal Diode (mirrored at address 0Bh) Stores the 8-bit low limit for the Internal Diode (mirrored at address 0Ch) Stores the integer portion of the high limit for the External Diode (mirrored at register 0Dh) Stores the integer portion of the low limit for the External Diode (mirrored at register 0Eh) Controls the general operation of the device (mirrored at address 03h) Controls the conversion rate for updating temperature data (mirrored at address 04h) 00h 00h Page 26
R/W R
REGISTER NAME Internal Diode Data High Byte
FUNCTION Stores the integer data for the Internal Diode
PAGE
03h
R/W
Configuration
00h
Page 27
04h
R/W
Conversion Rate
06h (4/sec) 55h (85C) 00h (0C)
Page 28
05h
R/W
Internal Diode High Limit Internal Diode Low Limit External Diode High Limit High Byte External Diode Low Limit High Byte
06h
R/W
Page 29 07h R/W 55h (85C) 00h (0C)
08h
R/W
09h
R/W
Configuration
00h
Page 27
0Ah
R/W
Conversion Rate
06h (4/sec)
Page 28
Revision 1.16 (03-15-07)
24
SMSC EMC1402
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
Table 6.1 Register Set in Hexadecimal Order (continued) REGISTER ADDRESS DEFAULT VALUE 55h (85C) 00h (0C) Page 29 0Dh R/W External Diode High Limit High Byte External Diode Low Limit High Byte One shot External Diode Data Low Byte Scratchpad Scratchpad External Diode High Limit Low Byte External Diode Low Limit Low Byte External Diode THERM Limit Channel Mask Register Internal Diode THERM Limit THERM Hysteresis Stores the integer portion of the high limit for the External Diode (mirrored at register 07h) Stores the integer portion of the low limit for the External Diode (mirrored at register 08h) A write to this register initiates a one shot update. Stores the fractional data for the External Diode Scratchpad register for software compatibility Scratchpad register for software compatibility Stores the fractional portion of the high limit for the External Diode Stores the fractional portion of the low limit for the External Diode Stores the 8-bit critical temperature limit for the External Diode Controls the masking of individual channels Stores the 8-bit critical temperature limit for the Internal Diode Stores the 8-bit hysteresis value that applies to all THERM limits Controls the number of out-of-limit conditions that must occur before an interrupt is asserted Stores the Beta Compensation circuitry settings for External Diode 1 Stores the ideality factor for External Diode 1 Stores the fractional data for the Internal Diode Controls the digital filter setting for the External Diode channel
25
R/W
REGISTER NAME Internal Diode High Limit Internal Diode Low Limit
FUNCTION Stores the 8-bit high limit for the Internal Diode (mirrored at address 05h) Stores the 8-bit low limit for the Internal Diode (mirrored at address 06h)
PAGE
0Bh
R/W
0Ch
R/W
55h (85C) 00h (0C) 00h 00h 00h 00h 00h Page 29 00h 55h (85C) 00h 55h (85C) Page 30 0Ah (10C) 70h Page 31 Page 30 Page 31 Page 30 Page 26 Page 30 Page 30
0Eh
R/W
0Fh 10h 11h 12h 13h 14h 19h 1Fh 20h 21h
W R R/W R/W R/W R/W R/W R/W R/W R/W
22h
R/W
Consecutive ALERT
25h
R/W
External Diode 1 Beta Configuration External Diode 1 Ideality Factor Internal Diode Data Low Byte Filter Control
08h 12h (1.008) 00h 00h
Page 33
27h 29h 40h
R/W R R/W
Page 34 Page 26 Page 35
SMSC EMC1402
Revision 1.16 (03-15-07)
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
Table 6.1 Register Set in Hexadecimal Order (continued) REGISTER ADDRESS FDh FEh FFh DEFAULT VALUE Table 6.20 5Dh 01h
R/W R R R
REGISTER NAME Product ID SMSC ID Revision
FUNCTION Stores a fixed value that identifies each product Stores a fixed value that represents SMSC Stores a fixed value that represents the revision number
PAGE Page 35 Page 35 Page 36
6.1
Data Read Interlock
When any temperature channel high byte register is read, the corresponding low byte is copied into an internal `shadow' register. The user is free to read the low byte at any time and be guaranteed that it will correspond to the previously read high byte. Regardless if the low byte is read or not, reading from the same high byte register again will automatically refresh this stored low byte data.
6.2
Temperature Data Registers
Table 6.2 Temperature Data Registers
ADDR 00h 29h 01h 10h
R/W R R R R
REGISTER Internal Diode High Byte Internal Diode Low Byte External Diode High Byte External Diode Low Byte
B7 128 0.5 128 0.5
B6 64 0.25 64 0.25
B5 32 0.125 32 0.125
B4 16 16 -
B3 8 8 -
B2 4 4 -
B1 2 2 -
B0 1 1 -
DEFAULT 00h 00h 00h 00h
As shown in Table 6.2, all temperatures are stored as an 11-bit value with the high byte representing the integer value and the low byte representing the fractional value left justified to occupy the MSBits.
6.3
Status Register
Table 6.3 Status Register
ADDR 02h
R/W R-C
REGISTER Status
B7 BUSY
B6 IHIGH
B5 ILOW
B4 EHIGH
B3 ELOW
B2 FAULT
B1 ETHERM
B0 ITHERM
DEFAULT 00h
The Status Register reports the operating status of the Internal Diode and External Diode 1 channels. When any of the bits are set (excluding the BUSY bit) either the ALERT or THERM pin is being asserted. The ALERT and THERM pins are controlled by the respective consecutive alert counters (see Section 6.11) and will not be asserted until the programmed consecutive alert count has been reached.
Revision 1.16 (03-15-07) 26 SMSC EMC1402
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
The status bits (except E1THERM and ITHERM) will remain set until read unless the ALERT pin is configured as a second THERM output (see Section 5.3.2). Bit 7 - BUSY - This bit indicates that the ADC is currently converting. This bit does not cause either the ALERT or THERM pins to be asserted. Bit 6 - IHIGH - This bit is set when the Internal Diode channel exceeds its programmed high limit. When set, this bit will assert the ALERT pin. Bit 5 - ILOW - This bit is set when the Internal Diode channel drops below its programmed low limit. When set, this bit will assert the ALERT pin. Bit 4 - EHIGH - This bit is set when the External Diode channel exceeds its programmed high limit. When set, this bit will assert the ALERT pin. Bit 3 - ELOW - This bit is set when the External Diode channel drops below its programmed low limit. When set, this bit will assert the ALERT pin. Bit 2 - FAULT - This bit is asserted when a diode fault is detected. When set, this bit will assert the ALERT pin. Bit 1 - ETHERM - This bit is set when the External Diode channel exceeds the programmed THERM limit. When set, this bit will assert the THERM pin. This bit will remain set until the THERM pin is released at which point it will be automatically cleared. Bit 0 - ITHERM - This bit is set when the Internal Diode channel exceeds the programmed THERM limit. When set, this bit will assert the THERM pin. This bit will remain set until the THERM pin is released at which point it will be automatically cleared.
6.4
Configuration Register
Table 6.4 Configuration Register
ADDR 03h
R/W
REGISTER
B7 MASK _ALL
B6 RUN / STOP
B5 ALERT/ COMP
B4
B3
B2
B1 DAVG_ DIS
B0
DEFAULT
R/W 09h
Configuration
RECD
-
RANGE
-
00h
The Configuration Register controls the basic operation of the device. This register is fully accessible at either address. Bit 7 - MASK_ALL - Masks the ALERT pin from asserting. `0' (default) - The ALERT pin is not masked. If any of the appropriate status bits are set the ALERT pin will be asserted. `1' - The ALERT pin is masked. It will not be asserted for any interrupt condition unless it is configured as a secondary THERM pin. The Status Register will be updated normally. Bit 6 - RUN / STOP - Controls Active/Standby modes. `0' (default) - The device is in Active mode and converting on all channels. `1' -The device is in Standby mode and not converting. Bit 5 - ALERT/COMP - Controls the operation of the ALERT pin. `0' (default) - The ALERT pin acts as described in Section 5.3. `1' - The ALERT pin acts in comparator mode as described in Section 5.3.2. In this mode the MASK_ALL bit is ignored. Bit 4 - RECD - Disables the Resistance Error Correction (REC) for External Diode.
SMSC EMC1402 27 Revision 1.16 (03-15-07)
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
`0' (default)- REC is enabled for the External Diode. `1' - REC is disabled for the External Diode 1. Bit 2 - RANGE - Configures the measurement range and data format of the temperature channels. `0' (default) - The temperature measurement range is 0C to +127.875C and the data format is binary. `1' -The temperature measurement range is -64C to +191.875C and the data format is offset binary (see Table 5.2). Bit 1 - DAVG_DIS - Disables the dynamic averaging feature on all temperature channels. `0' (default) - The dynamic averaging feature is enabled. All temperature channels will be converted with an averaging factor that is based on the conversion rate as shown in Table 5.1. `1' - The dynamic averaging feature is disabled. All temperature channels will be converted with a maximum averaging factor of 1x (equivalent to 11-bit conversion). For higher conversion rates, this averaging factor will be reduced as shown in Table 5.1.
6.5
Conversion Rate Register
Table 6.5 Conversion Rate Register
ADDR 04h
R/W
REGISTER Conversion Rate
B7
B6
B5
B4
B3
B2
B1
B0
DEFAULT 06h (4/sec)
R/W 0Ah
-
-
-
-
CONV[3:0]
The Conversion Rate Register controls how often the temperature measurement channels are updated and compared against the limits. This register is fully accessible at either address. Bits 3-0 - CONV[3:0] - Determines the conversion rate as shown in Table 6.6.
Table 6.6 Conversion Rate CONV[3:0] HEX 0h 1h 2h 3h 4h 5h 6h 7h 8h 9h 3 0 0 0 0 0 0 0 0 1 1 2 0 0 0 0 1 1 1 1 0 0 1 0 0 1 1 0 0 1 1 0 0 0 0 1 0 1 0 1 0 1 0 1 CONVERSIONS / SECOND 1 / 16 1/8 1/4 1/2 1 2 4 (default) 8 16 32
Revision 1.16 (03-15-07)
28
SMSC EMC1402
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
Table 6.6 Conversion Rate (continued) CONV[3:0] HEX Ah Bh - Fh 3 1 2 0 All others 1 1 0 0 CONVERSIONS / SECOND 64 1
6.6
Limit Registers
Table 6.7 Temperature Limit Registers
ADDR.
R/W
REGISTER
B7
B6
B5
B4
B3
B2
B1
B0
DEFAULT
05h R/W 0Bh 06h R/W 0Ch 07h R/W 0Dh
Internal Diode High Limit Internal Diode Low Limit External Diode High Limit High Byte External Diode High Limit Low Byte External Diode Low Limit High Byte External Diode Low Limit Low Byte
128
64
32
16
8
4
2
1
55h (85C) 00h (0C)
128
64
32
16
8
4
2
1
128
64
32
16
8
4
2
1
55h (85C)
13h
R/W
0.5
0.25
0.125
-
-
-
-
-
00h
08h R/W 0Eh
128
64
32
16
8
4
2
1
00h (0C)
14h
R/W
0.5
0.25
0.125
-
-
-
-
-
00h
The device contains both high and low limits for all temperature channels. If the measured temperature exceeds the high limit, then the corresponding status bit is set and the ALERT pin is asserted. Likewise, if the measured temperature is less than or equal to the low limit, the corresponding status bit is set and the ALERT pin is asserted. The data format for the limits must match the selected data format for the temperature so that if the extended temperature range is used, the limits must be programmed in the extended data format. The limit registers with multiple addresses are fully accessible at either address. When the device is in standby mode, updating the limit registers will have no affect until the next conversion cycle occurs. This can be initiated via a write to the One Shot Register or by clearing the RUN / STOP bit in the Configuration Register (see Section 6.4).
SMSC EMC1402
29
Revision 1.16 (03-15-07)
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
6.7
Scratchpad Registers
Table 6.8 Scratchpad Register
ADDR 11h 12h
R/W R/W R/W
REGISTER Scratchpad Scratchpad
B7 7 7
B6 6 6
B5 5 5
B4 4 4
B3 3 3
B2 2 2
B1 1 1
B0 0 0
DEFAULT 00h 00h
The Scratchpad Registers are Read Write registers that are used for place holders to be software compatible with legacy programs. Reading from the registers will return what is written to them.
6.8
One Shot Register
Table 6.9 One Shot Register
ADDR. 0Fh
R/W W
REGISTER One Shot
B7
B6
B5
B4
B3
B2
B1
B0
DEFAULT 00h
Writing to this register initiates a single conversion cycle. Data is not stored and always reads 00h
The One Shot Register is used to initiate a one shot command. Writing to the one shot register, when the device is in standby mode and BUSY bit (in Status Register) is `0', will immediately cause the ADC to update all temperature measurements. Writing to the One Shot Register while the device is in active mode will have no affect.
6.9
Therm Limit Registers
Table 6.10 Therm Limit Registers
ADDR.
R/W
REGISTER External Diode THERM Limit Internal Diode THERM Limit THERM Hysteresis
B7
B6
B5
B4
B3
B2
B1
B0
DEFAULT 55h (85C) 55h (85C) 0Ah (10C)
19h
R/W
128
64
32
16
8
4
2
1
20h 21h
R/W R/W
128 128
64 64
32 32
16 16
8 8
4 4
2 2
1 1
The THERM Limit Registers are used to determine whether a critical thermal event has occurred. If the measured temperature exceeds the THERM Limit, then the THERM pin is asserted. The limit setting must match the chosen data format of the temperature reading registers. Unlike the ALERT pin, the THERM pin cannot be masked. Additionally, the THERM pin will be released once the temperature drops below the corresponding threshold minus the THERM Hysteresis.
Revision 1.16 (03-15-07)
30
SMSC EMC1402
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
6.10
Channel Mask Register
Table 6.11 Channel Mask Register
ADDR.
R/W
REGISTER Channel Mask
B7
B6
B5
B4
B3
B2
B1 E MASK
B0 INT MASK
DEFAULT
-
-
1Fh
R/W
00h
The Channel Mask Register controls individual channel masking. When a channel is masked, the ALERT pin will not be asserted when the masked channel reads a diode fault or out of limit error. The channel mask does not mask the THERM pin. Bit 1 - EMASK - Masks the ALERT pin from asserting when the External Diode channel is out of limit or reports a diode fault. `0' (default) - The External Diode channel will cause the ALERT pin to be asserted if it is out of limit or reports a diode fault. `1' - The External Diode channel will not cause the ALERT pin to be asserted if it is out of limit or reports a diode fault. Bit 0 - INTMASK - Masks the ALERT pin from asserting when the Internal Diode temperature is out of limit. `0' (default) - The Internal Diode channel will cause the ALERT pin to be asserted if it is out of limit. `1' - The Internal Diode channel will not cause the ALERT pin to be asserted if it is out of limit.
6.11
Consecutive ALERT Register
Table 6.12 Consecutive ALERT Register
ADDR. 22h
R/W R/W
REGISTER Consecutive ALERT
B7 TIME OUT
B6
B5 CTHRM[2:0]
B4
B3
B2 CALRT[2:0]
B1
B0 -
DEFAULT 70h
The Consecutive ALERT Register determines how many times an out-of-limit error or diode fault must be detected in consecutive measurements before the ALERT or THERM pin is asserted. Additionally, the Consecutive ALERT Register controls the SMBus Timeout functionality. An out-of-limit condition (i.e. HIGH, LOW, or FAULT) occurring on the same temperature channel in consecutive measurements will increment the consecutive alert counter. The counters will also be reset if no out-of-limit condition or diode fault condition occurs in a consecutive reading. When the ALERT pin is configured as an interrupt, when the consecutive alert counter reaches its programmed value, the following will occur: the STATUS bit(s) for that channel and the last error condition(s) (i.e. EHIGH) will be set to `1', the ALERT pin will be asserted, the consecutive alert counter will be cleared, and measurements will continue. When the ALERT pin is configured as a comparator, the consecutive alert counter will ignore diode fault and low limit errors and only increment if the measured temperature exceeds the High Limit. Additionally, once the consecutive alert counter reaches the programmed limit, the ALERT pin will be asserted, but the counter will not be reset. It will remain set until the temperature drops below the High Limit minus the THERM Hysteresis value. For example, if the CALRT[2:0] bits are set for 4 consecutive alerts, the high limits are set at 70C, and none of the channels are masked, then the ALERT pin will be asserted after the following four measurements:
SMSC EMC1402 31 Revision 1.16 (03-15-07)
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
1. Internal Diode reads 71C and the external diode reads 69C. Consecutive alert counter for INT is incremented to 1. 2. Both the Internal Diode and the External Diode read 71C. Consecutive alert counter for INT is incremented to 2and for EXT is set to 1. 3. The External Diode reads 71C and the Internal Diode reads 69C. Consecutive alert counter for INT is cleared and EXT is incremented to 2. 4. The Internal Diode reads 71C and the external diode reads 71C. Consecutive alert counter for INT is set to 1 and EXT is incremented to 3. 5. The Internal Diode reads 71C and the external diode reads 71C. Consecutive alert counter for INT is incremented to 2 and EXT is incremented to 4. The appropriate status bits are set for EXT and the ALERT pin is asserted. EXT counter is reset to 0 and all other counters hold the last value until the next temperature measurement. Bit 7 - TIMEOUT - Determines whether the SMBus Timeout function is enabled. `0' (default) - The SMBus Timeout feature is disabled. The SMCLK line can be held low indefinitely without the device resetting its SMBus protocol. `1' - The SMBus Timeout feature is enabled. If the SMCLK line is held low for more than 30ms, then the device will reset the SMBus protocol. Bits 6-4 - CTHRM[2:0] - Determines the number of consecutive measurements that must exceed the corresponding THERM Limit before the THERM pin is asserted. All temperature channels use this value to set the respective counters. The consecutive THERM counter is incremented whenever any measurement exceed the corresponding THERM Limit. If the temperature drops below the THERM limit, then the counter is reset. If a number of consecutive measurements above the THERM limit occurs, then the THERM pin is asserted low. Once the THERM pin has been asserted, the consecutive therm counter will not reset until the corresponding temperature drops below the THERM Limit minus the THERM Hysteresis value. The bits are decoded as shown in Table 6.13. The default setting is 4 consecutive out of limit conversions. Bits 3-1 - CALRT[2:0] - Determine the number of consecutive measurements that must have an out of limit condition or diode fault before the ALERT pin is asserted. All temperature channels use this value to set the respective counters. The bits are decoded as shown in Table 6.13. The default setting is 1 consecutive out of limit conversion.
Table 6.13 Consecutive Alert / THERM Settings NUMBER OF CONSECUTIVE OUT OF LIMIT MEASUREMENTS 1 (default for CALRT[2:0]) 2 3 4 (default for CTHRM[2:0])
2 0 0 0 1
1 0 0 1 1
0 0 1 1 1
Revision 1.16 (03-15-07)
32
SMSC EMC1402
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
6.12
Beta Configuration Registers
Table 6.14 Beta Configuration Registers
ADDR.
R/W
REGISTER External Diode 1 Beta Configuration
B7
B6
B5
B4
B3
B2
B1
B0
DEFAULT
25h
R/W
-
-
-
-
ENABLE
BETA[2:0]
08h
This register is used to set the Beta Compensation factor that is used for the external diode channel. Bit 3 - ENABLE - Enables the Beta Compensation factor autodetection function. `0' - The Beta Compensation Factor autodetection circuitry is disabled. The External Diode will always use the Beta Compensation factor set by the BETA[2:0] bits. `1' (default) - The Beta Compensation factor autodetection circuitry is enabled. At the beginning of every conversion, the optimal Beta Compensation factor setting will be determined and applied. The BETA[2:0] bits will be automatically updated to indicate the current setting. Bit 2-0 - BETA[2:0] - These bits always reflect the current beta configuration settings. If autodetection circuitry is enabled, then these bits will be updated automatically and writing to these bits will have no effect. If the autodetection circuitry is disabled, then these bits will determine the beta configuration setting that is used for their respective channels. Care should be taken when setting the BETA[2:0] bits when the autodetection circuitry is disabled. If the Beta Compensation factor is set at a beta value that is higher than the transistor beta, then the circuit may introduce measurement errors. When measuring a discrete thermal diode (such as 2N3904) or a CPU diode that functions like a discrete thermal diode (such as an AMD processor diode), then the BETA[2:0] bits should be set to `111b'.
Table 6.15 CPU Beta Values BETA[2:0] HEX 0h 1h 2h 3h 4h 5h 6h 7h 8h - Fh ENABLE 0 0 0 0 0 0 0 0 1 2 0 0 0 0 1 1 1 1 X 1 0 0 1 1 0 0 1 1 X 0 0 1 0 1 0 1 0 1 X MINIMUM BETA 0.11 0.18 0.25 0.33 0.43 1.00 2.33 Disabled Autodetection
SMSC EMC1402
33
Revision 1.16 (03-15-07)
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
6.13
External Diode Ideality Factor Registers
Table 6.16 Ideality Configuration Registers
ADDR.
R/W
REGISTER External Diode 1 Ideality Factor
B7
B6
B5
B4
B3
B2
B1
B0
DEFAULT
27h
R/W
-
-
IDEALITY[5:0]
12h
These registers store the ideality factors that are applied to the external diodes. Table 6.17 defines each setting and the corresponding ideality factor. Beta Compensation and Resistance Error Correction automatically correct for most diode ideality errors, therefore it is not recommended that these settings be updated without consulting SMSC.
Table 6.17 Ideality Factor Look-Up Table SETTING 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh 10h 11h 12h 13h 14h 15h 16h 17h FACTOR 0.9949 0.9962 0.9975 0.9988 1.0001 1.0014 1.0027 1.0040 1.0053 1.0066 1.0080 1.0093 1.0106 1.0119 1.0133 1.0146 SETTING 18h 19h 1Ah 1Bh 1Ch 1Dh 1Eh 1Fh 20h 21h 22h 23h 24h 25h 26h 27h FACTOR 1.0159 1.0172 1.0185 1.0200 1.0212 1.0226 1.0239 1.0253 1.0267 1.0280 1.0293 1.0306 1.0319 1.0332 1.0345 1.0358 SETTING 28h 29h 2Ah 2Bh 2Ch 2Dh 2Eh 2Fh 30h 31h 32h 33h 34h 35h 36h 37h FACTOR 1.0371 1.0384 1.0397 1.0410 1.0423 1.0436 1.0449 1.0462 1.0475 1.0488 1.0501 1.0514 1.0527 1.0540 1.0553 1.0566
Revision 1.16 (03-15-07)
34
SMSC EMC1402
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
6.14
Filter Control Register
Table 6.18 Filter Configuration Register
ADDR. 40h
R/W R/W
REGISTER Filter Control
B7 -
B6 -
B5 -
B4 -
B3 -
B2 -
B1
B0
DEFAULT 00h
FILTER[1:0]
The Filter Configuration Register controls the digital filter on the External Diode channel. Bits 1-0 - FILTER[1:0] - Control the level of digital filtering that is applied to the External Diode temperature measurements as shown in Table 6.19. See Figure 5.2and Figure 5.3 for examples on the filter behavior.
Table 6.19 Filter Settings FILTER[1:0] 1 0 0 1 1 0 0 1 0 1 Disabled (default) Level 1 Level 1 Level 2 AVERAGING
6.15
Product ID Register
Table 6.20 Product ID Register
ADDR FDh
R/W R
REGISTER Product ID
B7 0
B6 0
B5 1
B4 0
B3 0
B2 0
B1 0
B0 0
DEFAULT 20h EMC1402
The Product ID Register holds a unique value that identifies the device.
6.16
SMSC ID Register (FEh)
Table 6.21 Manufacturer ID Register
ADDR. FEh
R/W R
REGISTER SMSC ID
B7 0
B6 1
B5 0
B4 1
B3 1
B2 1
B1 0
B0 1
DEFAULT 5Dh
The Manufacturer ID register contains an 8 bit word that identifies the SMSC as the manufacturer of the EMC1402.
SMSC EMC1402
35
Revision 1.16 (03-15-07)
DATASHEET
1C Temperature Sensor with Beta Compensation Datasheet
6.17
Revision Register (FFh)
Table 6.22 Revision Register
ADDR. FFh
R/W R
REGISTER Revision
B7 0
B6 0
B5 0
B4 0
B3 0
B2 0
B1 0
B0 1
DEFAULT 01h
The Revision register contains an 8 bit word that identifies the die revision.
Revision 1.16 (03-15-07)
36
SMSC EMC1402
DATASHEET
REVISION HISTORY
REVISION DESCRIPTION SEE SPEC FRONT PAGE FOR REVISION HISTORY DATE RELEASED BY -
3 D e PIN 1 IDENTIFIER AREA (D/2 X E1/2) 5 c
-
3
E1
E
2 8X b
SEE DETAIL "A"
TOP VIEW
END VIEW
C
A
SEATING PLANE A1 ccc C
SIDE VIEW
3-D VIEW
NOTES: 1. ALL DIMENSIONS ARE IN MILLIMETER. 2. TOLERANCE ON THE TRUE POSITION OF THE LEADS IS 0.065mm MAXIMUM. 3. PACKAGE BODY DIMENSIONS "D" AND "E1" DO NOT INCLUDE MOLD PROTRUSIONS OR FLASH. MAXIMUM MOLD PROTRUSIONS OR FLASH IS 0.15 mm (0.006 INCHES) PER END AND SIDE. DIMENSIONS "D" AND "E1" ARE DETERMINED AT DATUM PLANE "H". 4. DIMENSION FOR FOOT LENGTH "L" IS MEASURED AT THE GAUGE PLANE 0.25mm ABOVE THE SEATING PLANE. 5. DETAILS OF PIN 1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED WITHIN THE ZONE INDICATED.
H C 0.25 SEATING PLANE 0 - 8 4 L L1
GAUGE PLANE
UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND TOLERANCES ARE: DECIMAL 0.1 X.X X.XX 0.05 X.XXX 0.025 ANGULAR 1
THIRD ANGLE PROJECTION
80 ARKAY DRIVE HAUPPAUGE, NY 11788 USA
TITLE
DETAIL "A"
SCALE: 3/1
DIM AND TOL PER ASME Y14.5M - 1994
MATERIAL
NAME
DRAWN
DATE
-
S.K.ILIEV
CHECKED
7/05/04 7/05/04
SCALE
PACKAGE OUTLINE 8 PIN TSSOP, 3x3 MM BODY, 0.65 MM PITCH
DWG NUMBER REV
FINISH
S.K.ILIEV
APPROVED
MO-8-TSSOP-3x3
STD COMPLIANCE SHEET
D
Figure 7.1 8 PIN MSOP / TSSOP Package
SMSC EMC1402
PRINT WITH "SCALE TO FIT" DO NOT SCALE DRAWING
S.K.ILIEV
7/07/04
1:1
JEDEC: MO-187 / D
1 OF 1
37 DATASHEET
A2
Revision 1.16 (03-15-07)
Chapter 7 Package Information

▲Up To Search▲

Price & Availability of EMC1402-2-ACZL-TR

	To Download EMC1402-2-ACZL-TR Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .